Quick Answer: Missouri Metal Buildings
A 40x60 costs $16,800-$57,600 as a kit and $45,000-$123,900 installed. Missouri metal buildings follow local codes, because the state leaves adoption to counties and cities, so call your county before you order. Farm shops, machine sheds and hay barns lead in the north-central counties, and the Bootheel adds earthquake design. Pull your address from the ASCE Hazard Tool, then compare free quotes.
Simplify your research by letting us do the work for you.

Missouri farm country asks a lot of a building. Hay goes up in the summer, grain comes in at harvest and the equipment needs a roof that survives a spring storm line. A steel frame handles all three, and good planning keeps Missouri metal buildings toward the low end of their price range. This guide to Missouri metal buildings covers what a building costs by size, how the weather changes between the river bottoms and the Bootheel, and who issues the permit.
It is written for people building in north-central and west-central Missouri: Chariton, Carroll, Caldwell, Livingston, Ray, Lafayette and Saline counties, around Chillicothe, Carrollton, Marshall, Lexington, Richmond and Keytesville. Those are grain, hay and cattle counties east of Kansas City. The advice on Missouri metal buildings fits farm shops and machine sheds anywhere in the state. A free quote turns these ranges into a number for your own farm or lot.
Get Up To 5 Free Quotes for Your Building
- Enter your size and county once
- Compare bids from several suppliers
- Zero obligation

What Missouri Metal Buildings Cost by Size
Start with the building itself. The price of Missouri metal buildings has two layers. The kit means steel framing, wall and roof panels and trim, trucked to your farm lane. The installed figure also pays for concrete, the erection crew, grading and county permits. Every number below is a range, because ground, doors and finish differ from one Missouri parcel to the next.
| Size | Floor area | Kit only | Installed | Typical use |
|---|---|---|---|---|
| 30x40 | 1,200 sq ft | $10,800-$38,400 | $25,800-$75,900 | Farm shop or hay storage |
| 40x40 | 1,600 sq ft | $11,200-$38,400 | $30,600-$85,500 | Heated shop or garage |
| 40x60 | 2,400 sq ft | $16,800-$57,600 | $45,000-$123,900 | Machine shed or repair shop |
| 40x80 | 3,200 sq ft | $22,400-$70,400 | $59,400-$155,900 | Combine and tractor storage |
| 60x100 | 6,000 sq ft | $42,000-$132,000 | $109,800-$284,700 | Grain handling or commodity barn |
Larger Missouri metal buildings cost less per square foot, because the frame, the engineering and the crew's travel spread across more floor. The 40x60 below shows how the lines stack up. Metal building prices uses the same method for other sizes.
| Line for a 40x60 | Low | High |
|---|---|---|
| Kit, materials only | $16,800 | $57,600 |
| Concrete slab, 4 inch | $14,400 | $28,800 |
| Erection crew | $12,000 | $28,800 |
| Site preparation | $1,300 | $5,600 |
| Permits | $500 | $3,100 |
| Installed total | $45,000 | $123,900 |
That is roughly $19 to $52 per square foot installed at this size, a figure that answers the common search for a metal building cost per square foot. Overhead doors, insulation, wiring and an interior finish all cost more on top. Heating a shop with a mini-split adds $2,000-$9,200, and spray foam on the walls and roof is $1.00-$4.50 per square foot.

Why Two Farm Buildings of One Size Price Differently
Two neighbours in Livingston County can order the same 40x60 and receive very different bids. Where a quote lands between the low and high figure depends on five things about the property and the county.
The Cost Drivers That Matter Here
- Wind and snow engineering: a design for a tornado-prone open field or a heavier snow load means stronger frames and stamped drawings.
- Delivery distance: a gravel county road ten miles from the nearest town costs the truck more than a paved lot in Marshall.
- Local labour: a crew that travels from Kansas City or Columbia charges for the drive, and metro crews charge more than rural ones.
- Site work: a building on a river-bottom field needs more fill and drainage than one on a ridge.
- Soil: clay that swells and shrinks can mean a thicker slab or deeper footings.
Steel against wood, kit against turnkey
Steel does not rot and insects ignore it, which matters in a damp hay barn. Buying a kit means you pay for materials and find your own crew. Turnkey hands the whole job to one contractor, which is easier when the farm is busy. Pole-barn builders sell a different wooden system, covered on pole barns versus metal buildings.

Weather From the River Bottoms to the Bootheel
Missouri weather is not one thing. Missouri metal buildings are designed to the site, not the state. Wind, snow and seismic values come from ASCE 7 and change from one address to the next. Every code figure on this page is drawn from published documents for orientation only, is not engineering advice, and must be confirmed with the building department that will review your plans and the engineer who seals them — Metal-Buildings.org is not responsible for design decisions made from these numbers. Pull your own address from the ASCE Hazard Tool before you order anything.
| Region | What drives the design | What to ask your engineer |
|---|---|---|
| North-central and west-central (Chillicothe, Carrollton, Marshall, Lexington) | Severe thunderstorms, straight-line wind, tornadoes, winter snow and drifting | Wind speed, ground snow load and drift at your address |
| Kansas City and the Missouri River corridor | Thunderstorm outflow and tornado season | Risk category and wind exposure |
| Ozarks (Springfield area) | Storms, ice and rocky ground | Footing depth over limestone |
| St. Louis and the Mississippi corridor | Storms, plus distant earthquake shaking | Seismic design category |
| Bootheel (New Madrid zone) | Earthquake shaking, soft river soils | Seismic design category and soil report |
Tornado wind is the item farm owners ask about first. Missouri sees dozens of tornadoes in a typical year. A pre-engineered building is designed to a wind speed for its location, not to survive a direct hit. Doors are the weak point in a storm, so ask for door ratings that match the wall design. The wind load calculator shows how the numbers work.
Snow is mild next to the northern plains but not absent. Drifts pile against a taller wall or a lean-to, and the engineer accounts for them at your address. In the Bootheel, the New Madrid Seismic Zone spans more than 100 miles and averages over 200 small earthquakes a year, according to the State Emergency Management Agency. Missouri's emergency managers say similar quakes to those of 1811 and 1812 still pose a risk today.
Price Your Building Today
- Up to 5 competitive bids
- Free and zero obligation
- Compare quotes and decide

Permits: Who Issues One and What a Farm Building Needs
Missouri leaves most code decisions to local government, so permits for Missouri metal buildings come from the county or the town. The International Code Council notes that although most relevant building codes are adopted locally, the state adopts codes for state-owned buildings. The state's own Department of Natural Resources says the codes in force are listed by county and city, and that the most current answer comes from the local jurisdiction. See the ICC adoption map for Missouri for the overview.
So the first call is to your county. Some counties have adopted the International codes, some adopt for the town only and some have no building code at all outside city limits. Missouri's county code statute lets first and second class counties adopt building regulations, and a county without a code before 2001 needs a vote of its people to start one. That is why a Carroll County farm and a Boone County shop can face different rules. Plan your Missouri metal buildings around the local answer.
| Question | Who answers it |
|---|---|
| Does the county adopt a building code? | County commission or resource management office |
| Does the town inside the county adopt one? | City hall or the town's building inspector |
| Is a farm building exempt? | The county, in writing, before you pour concrete |
| Does the lender or insurer want plans? | Your lender and your insurance agent |
The county code statute I read has no farm exemption of its own. If one exists where you live, it is the county's rule, and these are normally tied to use: a building that is not used only for farming can lose it. Ask for the exemption in writing, ask about the electrical work and septic if you plan any, and keep the letter. A building with a lender behind it often needs sealed plans whether or not the county asks. See metal building permits and codes for the general picture, and the USDA Farm Service Agency if you are financing a farm building.

Foundations, Frost and Soil
Frost depth is set by the jurisdiction, not by the state. The adopted residential code carries a table where each county or city fills in the minimum depth of a footing below grade, so there is no single Missouri number to quote. Ask the building department or your engineer for the value at your address, and never accept a guess from a forum.
North Missouri soils behave differently from the Ozarks. Heavy clay and silty river-bottom ground swell when wet and shrink when dry. Along the Missouri River, fill and drainage often matter more than the footing itself. In the Ozarks, shallow rock changes how deep you can dig. A soils report is cheap next to a cracked slab.
A slab on frost-protected footings
A heated building with a concrete stem wall puts the slab on a short frost wall that reaches below the local frost line. An unheated hay shed can sit on piers or a thickened edge. Both options are an engineer's call at your site.

What People Build in Farm Country
Chariton, Carroll, Ray and the counties around them are grain, hay and cattle country. Missouri metal buildings there follow the work. Here is what they look like.
| Use | Common size | What to plan for |
|---|---|---|
| Farm shop | 40x60 | Tall door for a combine, insulated and heated, a slab with floor drains |
| Machine shed | 40x80 or larger | Clear span, wide doors and eave height for a planter or sprayer |
| Hay storage | 30x60 and up | Open or partly enclosed walls for airflow, a dry floor and a fire plan |
| Grain handling | 60x100 | Heavy floor loads and dust control |
| Livestock | 30x60 and up | Galvanized rather than Galvalume panels, ventilation and a washable floor |
Each of these has its own guide. Farm shop buildings and farm equipment storage buildings cover the first two. The metal hay barn guide covers hay, and metal livestock shelters covers cattle. Ammonia from animals attacks the aluminum in Galvalume, so a confinement building belongs in galvanized steel.
Farm buildings are also treated differently for tax. A general-purpose machine shed or farm shop is 20-year property, and a single-purpose livestock structure can qualify for faster treatment. Ask your tax adviser, because a building is not written off in the first year the way equipment can be.

Delivery and Erection
Missouri metal buildings ship as a kit on flatbeds, usually in several weeks, and the truck needs a firm road to the pad. Farm lanes with soft shoulders or low bridges can add a day and a forklift. Ask how the supplier handles unloading, and where the crew stages the steel on a wet spring field.
Erection of Missouri metal buildings takes a crew of several people a few days for a 40x60 once the slab has cured. Crane work and tall eaves push the labour line up. If you plan to build it yourself, steel erection is dangerous work, and OSHA's steel erection rules set the minimum.
Do not skip the call before ordering
Order your Missouri metal buildings kit after the county confirms the permit rules. Frames are engineered to the loads of the site, and a change after the order costs money.

Kansas City, Columbia, Springfield and St. Louis
Four metros each get a short note on Missouri metal buildings.
Kansas City
Missouri metal buildings near Kansas City face a patchwork. The city and its suburbs are many building departments, each with its own adopted code. Wind and tornado exposure matter on the open ground east of the city.
Columbia
Around Columbia, ask the county whether it has adopted a building code; where it has, a shop goes through plans review. Farm ground is a question for the county.
Springfield
The Ozarks mean rock, slope and runoff. Ask your engineer about footings. Slopes shape Missouri metal buildings there.
St. Louis
St. Louis is in the shaking range of the New Madrid zone, so the seismic design category deserves a real look.


Cost Questions Missouri Buyers Type Into Bing
Missouri searchers ask the same short questions about Missouri metal buildings again and again. Here are plain answers, drawn from the same ranges as the tables above.
Steel building prices and installed prices
Steel buildings prices run $7 to $32 per square foot as a kit, depending on size. Installed, a 40x60 is $45,000-$123,900 and a 60x100 is $109,800-$284,700. The range is wide because the frame, doors and site work vary. The metal building cost estimator gives a range for your size.
A red iron shop, 60x100, with concrete and insulation, erected
Concrete and erection are already inside the installed figure of $109,800-$284,700. Insulation is extra. Spray foam runs $1.00 to $4.50 per square foot of surface, so a building this size adds a meaningful line. Red iron frames sit toward the upper half of the range. Red iron buildings explains the framing.
A heated 40x60 garage with a concrete stem wall
Start from $45,000-$123,900 installed for this kind of Missouri metal buildings project. A stem wall and a heated slab raise the concrete line, and a mini-split adds $2,000-$9,200. See the foundation section above for how the wall works.
Pre-engineered metal buildings in Missouri
A pre-engineered building arrives as a designed kit with sealed drawings. Most counties and lenders want them. Pre-engineered metal buildings explains what is in the package.
For a 40x40, expect $11,200-$38,400 as a kit and $30,600-$85,500 installed. For a 40x80, expect $22,400-$70,400 and $59,400-$155,900. Searchers also ask for the best company. This page names none, because the right supplier is the one whose bid fits your drawings.
Building across the state line
Looking beyond Missouri metal buildings? See find metal buildings by state for the full list, and Texas metal buildings or Ohio metal buildings for the nearest pages we have written.
Frequently Asked Questions
A 40x60 runs $16,800-$57,600 as a kit and $45,000-$123,900 installed. Per square foot, small buildings run dearer and big ones cheaper. Your own figure depends on wind or snow engineering, eave height and site work.
A 40x80 has 3,200 square feet, enough for a combine and a tractor. Expect $22,400-$70,400 for the kit and $59,400-$155,900 installed.
Installed, a 40x60 works out to roughly $19 to $52 per square foot. A big machine shed lands near the bottom of that span and a small garage near the top.
Yes. The metal building cost estimator gives a range once you enter a size. For firm numbers on your parcel, the quote form returns bids from suppliers.
Usually, but it depends on the county or town. Permits for Missouri metal buildings are local. Missouri leaves building codes to local government, so call the county first. Some counties exempt qualifying farm buildings, and you should get that in writing.
Not for private buildings, so Missouri metal buildings follow local rules. The state adopts codes for state-owned buildings, and counties and cities adopt their own. Check whether yours does.
Not by one statewide rule. Any exemption is set by the county and usually depends on the building being used only for farming. Ask the county commission or resource office.
Below the local frost depth, which each jurisdiction sets in its adopted code. Your building department or engineer can give the number for your address.
It is engineered to a wind speed for its location, which is not the same as surviving a direct hit. Ask for door ratings and anchorage that match the design.
Yes. The New Madrid zone sits in southeast Missouri, and the engineer sets the seismic design category for your site.
A kit looks cheaper, but someone has to schedule the slab, the crane and the crew, and harvest can get in the way. Turnkey gives you one contractor to call.
Conclusion
Missouri rewards a phone call before a purchase order. Pull your hazard numbers, ask your county about its code and the farm exemption, and test the soil. Then your Missouri metal buildings project goes up on schedule.
The price you want for Missouri metal buildings is a quote for your parcel, not an average. One short form brings several bids for the same building, so you can compare like with like.
Related Resources
- Metal Building Prices: Costs by Size
- Farm Building Cost
- Metal Building Permits and Codes
- Farm Shop Buildings
- Metal Building Kits
- Building Codes by State: Editions, Enforcement and Farms
- Iowa Metal Buildings
- Tennessee Metal Buildings
- Arkansas Metal Buildings
- Oklahoma Metal Buildings
- Nebraska Metal Buildings
Ready to Price Your Missouri Building?
- One short form, up to 5 bids
- Compare quotes and decide
- Free expert consultation
